Ion bonding gun finish6/5/2023 ![]() coating performs well, but astetically, not great. I've got several CrN guns but haven't been impressed with the appearance. if you want silver, I'd suggest hard chrome plate, but it's getting harder to find good platers with the increasing reglatory restrictions on plating operators. If you want colors this is one way to get them. TiCN - Dark blue - close to traditional bluing These vacuum processes are also called CVD (chemical vapor deposition) or PVD (Physical vapor deposition) there are lots of subsets in these such as ALD (atomic layer deposition), Plasma, Sputtering, argon beam, and others.Ĭolors are highly dependant on process conditions and s toichiometry but here are some reasonable overviews. if you've seen the "rainbow" colors, that is effectivly a poorly controlled vapor deposition process that results in non uniform thin layers that refract different wavelengths of light to get the rainbow or irridescent effect. Kimber uses them a lot on thier higher end guns. they perform well in all applications as they were designed for much more demanding environments than we use. I've been using CrN, AlTiN,ZrN and other coatings for many years on cutting tools and guns. NONE of them are thick enough to impact the clearances we have in bullseye guns. Other "nitrides" are vacuum deposited finishes and there are numerous ones. "black nitride" is typially salt bath nitride which is also called tenifer by glock and has lots of other trade names. To clarify, the CPII is ceracoat, got a fancy name and "nano" buzzwords in it, but pigment, polymer, thermally cured all scream "paint". Last edited by shanneba on Mon 11:34 am edited 1 time in total Protect your firearm with Armoloy TDC - Armoloy of Fort Worth, Texas () Wear values exceeding 1.2 TWI limits established within AMS 2438Īrmoloy Coating, Protective Metallic Coatings | Metal Surface Treatment & Finishing ()įirearms pricing from Armaloy of Ft.Corrosion resistance equivalent to 440C stainless steel.0001/.0003" (2.5/7.5 microns), Armoloy TDC is effective at deposits as low as. Sounds like maybe it was an Armaloy finnish- that was a popular firearm finish back in the 80s-90sĪrmoloy TDC : The Foundation of the Big 7 - Armoloy of Illinois () I shot about 5,000 rounds+ per year for 3 years with that pistol and it never showed the wear at all. This was no standard anesthetic chrome but the correct, industrial-style chrome with the media-blast look you find on pump shafts and bearing races. The frame and slide had been hard-chromed (or nickel). It was very well done, possibly by Behlert or Gray. I have to contact him about something and will see if he minds it being passed to you given your current location.NukeMMC wrote:I had a 38super Caspian hi-cap that had been built in the early 90s. I know he has an email, but dont know if he wants it out. Ryan mentioned they deal with alot of 'smiths. No need for the extra step if Rusty is going to assemble it anyway. I'm sure that Rusty could do the work, then send it direct to Ryan and back. ![]() I thought about it and went all satin black. Rich, originally I was going to go with a "chrome-like" finish on the barrel and the hammer, just for a little "bling." Ryan said they have a finish that has the appearance of hard chrome, but if I recall correctly, it wasnt as hard as the black PVD, maybe 60-70 versus 70-90. An e-mail address for Ryan would be great too. The reason I ask on if they over a 'chrome'-type coating is I have an old 1911 that I want to get done in the classic 2-tone. After the work is done though, I send all the parts to Ion Bond then right? I'll have Rusty do the re-assembly too.ĭoes everything just get the PVD (since they are my 'black' guns)? Or do various parts get different coatings. On my Kidd Vipers, I'm having Rusty go through them and give 'em a tune up. So does Ion Bond have a "chrome"-like finish (i.e. ![]()
0 Comments
Leave a Reply. |